These are the steps to configure the Ubiquiti Bullet. Mode of operation that will be connected to a wireless router in the WAN port so wireless router. Like all Ubiquiti equipment the Bullet is capable of being set in any wireless mode – access point, station, bridge, router, AirMax (for P2P/P2MP) AP/station. Bullet2HP, Bullet2-HP by Ubiquiti Networks, High Power GHz bg AP or Client Bridge, CPE, Outdoor, Bullet2HP b/g mW Indoor/Outdoor Access Point / Client Device by Ubiquiti Networks Pre-Configure, Burn In & Test.

Author: Mezigul Mozuru
Country: Estonia
Language: English (Spanish)
Genre: Software
Published (Last): 21 November 2006
Pages: 173
PDF File Size: 4.89 Mb
ePub File Size: 7.53 Mb
ISBN: 753-2-77264-533-4
Downloads: 29539
Price: Free* [*Free Regsitration Required]
Uploader: Shaktilkis

The Bullet HP’s are commonly used for long distance PtP connections acess can accept any N-type antenna from a 24dBi parabolic directional to a smaller 5dBi omni-directional.

Help – Simple set up for Bullet M2HP / Wireless router / Computer to receive wifi internet access

Published on September 14th, This is also the website where you are invited to write an article on a boating topic, show bullet2hp your latest project or just share your knowledge with other boaters by participating in our Boating How To Forums. The Bullet Lan will then connect to one of the switch ports on the Netgear. Contact Us Boating How To.

Are you asking how to setup the router? About Us We are the website for boating enthusiast from the novice to the old salt desiring to learn more about their boat or boating configuratoon general. What you are getting is a system that has been programmed so it is roughly plug it in, install some software and you are up and running.


Bridge Management IP Address: I saved that configuration as ‘config Attachment This setup is nothing more than a repeater that boost the signal to a usable level, you still have to have someone providing internet access either via a free wifi access point or provide you with the proper login information for secure wireless networks.

Give people incorrect information on nullet2hp Post box pictures without discussion.

You’ll also have a narrower vertical beam 15 degrees which will have a negative impact cobfiguration clients who are not located on the same floor as the antenna in the same building. I attached the wan port on my tplink router to the lan port on the m2.

Ubiquiti Bullet2HP Installation and Onboard Wifi installation –

I appreciate it a great deal. I’ll certainly be adding this to my boat for the summer. Same password for both? This system will boost the signal making connections easier. DennisG on Cruiser’s Forum see above has: They both have phone support, the main difference is that Island Time knows what you are calling about and is intimately familiar with their software and the system, while Ubiquiti techs handle all types of installation and components.

Thus, in the case of the Platypus boat, the radio must be configured in Bridge mode. In Linux, we can manually connect to the bullet through the ifconfig command. A walkthrough step-by-step guide on how to set up a Ubiquiti device to connect to a remote access point or hotspot in order to share internet with multiple local devices. It should really give you a reasonable range assuming the antenna’s are correct.



At that point it was a simple wireless connection from my laptop to the router. What about connecting the router?

To begin this process I scoured the internet trying to find out as much information as I could about the hows, whats and whys. I have no idea where to put it. First of all, thanks for a very informative article – one that I followed pretty much to the letter. Actually, he missed last year.

Tim, thanks for this article, I’ve sent your link to a few coworkers to upgrade some of our stuff. I see it when we use a bulet2hp broadband card with a broadband router like cradlepoint. When in doubt, contact the mods and ask. I spent quite a bit of time corresponding with the folks at ubiquity getting help.

We also cover common procedures such as “how to anchor properly” or “how to lock through a dam”. For this initial setup, it is recommended to connect the Bullet to a conventional computer, as the configuration is done via browser or to a Raspberry running a graphical interface OS. There might be a better way to do this I’m all ears but this works well for me.

TimG – February 16th, You will find a wide range of topics covered in both articles configurqtion videos, to include boat repair and maintenance, marine engine cooling systems, marine electrical systems, installing thru-hulls, or installing a windlass.

TimG – February 21st,