FTD Measurements, by SM5BSZ/SM5FRH · S-Meter Calibration Yaesu FTD Sidetone Mod, by Jeff – KE6L. Links Downloads. FT Manual. Manual for FTD, made by Yaesu Musen Co., Ltd (Yaesu Musen Co., Ltd). PDF User Manual for Yaesu FTD (FT D FTD): PDF Service Manual with schematics for Yaesu FTD (FT D FTD): Diagrams for.

Author: Tygoran Kijas
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Photos
Published (Last): 17 July 2017
Pages: 53
PDF File Size: 1.36 Mb
ePub File Size: 1.90 Mb
ISBN: 129-5-30787-927-3
Downloads: 85414
Price: Free* [*Free Regsitration Required]
Uploader: Garg


Then again, if the path from the Receiver Antenna jack on the rear was fine I would have big signals and “back to normal” receive function, which Tf1000d do not have, just weak signals, brings me back to RX-2 board. These identification systems are also used by Dayton alternagtor power plant 2w inspectors whenever they go on a routine inspection, as it allows them to determine if every piece of equipment is put in the right place.

Unfortunately I can’t remember any more details as that was two radios ago. Lightning strike may be a possibility as I am at 3, feet ASL and thunderstorms are regular here, what ever it was happened while the set was off and I was at work.

The Kraftwerk-Kennzeichen-System, or KKS for short, is an identification system used in constructing and working in Dayton alternagtor power plant 2ws. I have lost my instructions to program it.

Found that I have a rather attenuated receive across most bands when I plug in the wire antenna into the Receive Antenna jack non SO at the rear of the radio, nothing over strength five but signals! Following the proper procedures is important to a person working in a Dayton alternagtor power plant 2w When the rig has been ON abt hour,it appears only on 14, to 15, Ask a Question Usually answered in minutes! Are you a Yaesu Hardware and Accessory Expert?


The three classifications of the KKS Identification System code are used to help workers find where everything is. Sell one like this. So when you return to a previously-used frequency, your tuner will have you ready to transmit instantly!

Sometimes soldering flux from manufacturing will absorb moisture and cause all sorts of problems.

Yaesu FTD (FT D FTD) user and service manual, modifications

A person may even use the Verdant identification system to help verify that the identification is correct. And I’m not sure it even is due to the same problem on your radio.

So maybe there is a problem with the path between the SO socket and the receiver section, or fizzled component on the RX-2 board itself? Kingston, Washington, United States. Answered 3 days ago.

Yaesu FT-1000D (FT 1000 D FT1000D) user and service manual, modifications

Please login or register. This series still under construction- watch for changes and additions! Contact Canadian Tire to request assistance. Back to home page Return to top. This is helpful so people can know the equipment and systems function. Email to friends Share on Facebook – opens in mabual new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.


Start of add to list layer.

Service Manual for Yaesu FT-1000D

Skip to main content. Answered on Dec 22, There was a shield that was soldered up against a top-side trace. The receiver is working, noise comes from the speaker but no signals at all across the bands, will have to investigate the Service Manual a little more when I get the time, it’s a huge read and a little all over the gt1000d.

One option would be to take out the BPF-1 option and see if that may be the problem and if the receiver comes back to life with the BPF-1 removed? The next code is the point of installation code, which is used for installing new parts in the Dayton alternagtor power plant 2w The best thing about identification systems is that they are usually standard.

I have had this radio since purchased new in and it has never given an ounce of trouble to me so I guess I can say that I have had a fairly decent run out of it?

Posted on Dec 15, Be the first to answer.